For
information on any of the following please click on link:
Amplimesh
Sectional & Pedestrian Doors
|
Where
free airflow through your garage area is required,
the Amplimesh Sectional Overhead Door provides just
that. The expanded aluminium mesh panel provides
both security and ventilation of approximately 80%.
Amplimesh
is WELDED to frame.
|
|
Slatted Aluminium Sectional Door
|
The
Slatted Aliminium sectional overhead door provides
approximately 40% airflow.
Aluminium slats are WELDED to frame.
|
FlatPanel
/ Amplimesh Panel Sectional Door
|
The
Flatpanel / Amplimesh Panel sectional overhead door,
panels can mixed to suit customers individual requirements. |
|
Opal
Sectional Door
|
The
Opal sectional overhead door provides no airflow
but some light.
|
AMPLIMESH
SECTIONAL OVERHEAD DOOR
 |
The
Accent Garage Doors Sectional Overhead Door is a high
cycle commercial grade door that is both stylish and
robust. It is ideally suited to carparking in home units
and office buildings where security, reliability and
ventilation issues are paramount. |
AMPLIMESH
DOOR PANELS
The
door panels are made from a heavy duty aluminium extruded
box section frame encasing a 68A style amplimesh sheet.
The sheet is held tightly in place via a U channel, constructed
into the frame and then via numerous 3/16 rivets.
|
|
|
|
AMPLIMESH
68A GRILLE
|
HEAVY
DUTY EXTRUSION
(Bottom Panel- 68A Grille)
|
DOOR
HARDWARE
Sectional
overhead doors are made by hinging together 4 or more (
depending on height) horizontal panels, that lift up and
when in the open position sit parallel to the ceiling. The
benefits of the sectional overhead door are that, at no
time during its opening operation the door panels do not
protrude past the vertical position of the door. Another
benefit is that no opening clearance is lost when the door
is fully open as long as a minimum headroom of 250mm is
available.
Back
to the Top
ACCESSORIES
•Where
Posts are required we will unless otherwise instructed use
3mm X 150 X 50 RHS galvanised posts. These posts can be
powdercoated to match the door.
•Where a Pedestrian Access door is required we can
build a door to match the sectional overhead door. See picture
below. This door can be fitted with a number of different
locks and hinges as per client specifications.
•These
doors are designed for Automatic Operation. Our preferred
automatic door opener is the Robot Electronics GD-81/H.This
opener has been designed as a heavy duty high cycle door
opener that can be fitted with logic controls, auto closing
timer and photoelectric safety beams. It requires a 240V
power point. Various access control systems, such as remote
handsets, card readers, keypads, keyswitches or electromagnetic
induction loops can be fitted to these openers.
Back
to the Top
INSTALLATION
REQUIREMENTS
Headroom
| Standard |
365mm
+ 60mm Auto Opener |
| Low
|
190mm
+ 60mm Auto Opener |
Sideroom
| Using
Standard headroom |
110mm |
| Using
Low headroom |
140mm |
NOTE:
These headroom and sideroom requirements are to be used
as a guide only. Through various techniques we can often
reduce the size of these requirements. This however, is
depending on various features to the opening.
Back
to the Top
PRODUCT
INFORMATION
Should
you have any questions please contact Accent Garage Doors
where we can advise you on technical specifications, product
pricing or product alternatives that would best suit your
application.
Back
to the Top
SPECIFYING
THE ACCENT AMPLIMESH SECTIONAL DOOR
Accent
68A style Commercial grade sectional overhead door comprising
of horizontal panels hinged together that operate along
a horizontal and vertical track system under tension via,
a torsion spring system that controls the door by use of
multi wire galvanised steel cables. The door panels will
be manufactured using expanded aluminium mesh, inside hollow
box section aluminium extrusion complete with muntins as
required for frame rigidity. Automatic operation to use
a ½ HP heavy duty automatic door opener with logic
controls, auto closing timer and photoelectric safety beams.
Access systems client to specify remote handsets, cardreaders
, keyswitches induction loop and keypads etc.
Back
to the Top
ARE
ALL AMPLIMESH SECTIONAL OVERHEAD DOORS THE SAME?
NOT
BY A LONG SHOT.
Your
decision on which basement security door to buy is probably
far more important than you think.
Other
than your lift, this door will be the largest moving item
in your building. As a consequence of this, it has many
moving parts that will eventually over time fail and require
replacement. Unfortunately, with each failure comes added
cost, a temporary loss in security and an overall inconvenience
to the car park users. These factors, coupled with the high
frequency of use this door must endure, emphasise the importance
of choosing a strong, reliable and robust door.
What
features does Accent Amplimesh Sectional Overhead door have
that sets it apart from the crowd?
•Our
aluminium extruded intermediate rails have been engineered
in the following shape which is substantially stronger than
many of our competitors.
Many
of our competitors use the following frame:
•Our
top and bottom aluminium extruded rails are engineered differently
to the intermediate rails, in that they are extruded in
the following shape:
110mm
This
extrusion is 110mm in height and consequently is much stronger
that the Intermediate rails. Our reason for this is because
experience has shown us that it is the top and bottom rails
that are impacted the most by vehicles and thieves. By strengthening
these two rails, we have reduced the potential damage to
our door. It is worth noting that many of our competitors
only use the smaller intermediate rail for their top and
bottom rails.
•Our
Amplimesh sheet is welded into the frame which;
A) Prevents thieves from ripping the sheet out of the frame.
B) Significantly reduces the noise emitted during the operation
of the door.
•Our
tracks, hardware and hinges are made from galvanized or
zincannealed steel.
•We
use 4mm steel cables to lift the door. Many competitors
only use 3mm cables. Over time cables will fray and require
replacement, however, as the 4mm cables are 33% stronger
than the 3mm cables they will last significantly longer.
•We
only use 1.6mm heavy duty tracks and our pulley wheels are
cast iron (not plastic like many of our competitors).
•We
use 3mm thick galvanized steel hinges. Many of our competitors
only use 1.6mm.
•Our
rollers are ball bearing machined steel with nylon coating
which are extremely durable and quieter than non bearing
wheels.
•We
use quality high cycle springs. Our minimum wire size is
6.3mm ranging to 8mm depending on the weight of the door.
Many of our competitors use 4mm wire springs that have a
much less life cycle than the 7mm or 8mm wire springs.
•We
use Irwin Sick photoelectric safety beams which are made
in Germany. Many of our competitors use Asian made domestic
quality safety beams.
•All
wires are run inside surface mounted flexible conduit and
not just glued or plugged to the walls.
•We
weld a steel plate around the push arm that prevents thieves
releasing the manual override ring from outside the door
via a rod.
•Accent
Garage Doors is a strong, reliable company who over its
25 years has grown to be Sydney's largest supplier of doors
to the home unit market
•Accent
Garage Doors' market share, reputation and manufacturing
techniques allow us to supply a superior product at a very
competitive price.
•As
we do so many of these types of doors, we are able to maintain
experienced installers who specialize in these types of
doors. A top quality door not installed perfectly can lead
to countless failures.
•Accent
Garage Doors prides itself on its flexibility and ability
to tailor its products to a client's specific needs. Should
you have any unusual circumstances or concerns please do
not hesitate to contact us.
Please
use this as a guide as to what questions to ask when comparing
quotes so that you can make an informed judgement when assessing
which quote will provide you with the best quality door
and value for money.
Back
to the Top
